FlyAmsterdam v1.3 Update

[derekv06]

Does this work directly with True Earth Netherlands or do we have to make the manual changes again ?

Thanks.

Regards, Gerard

Yep +1 ... Anybody can confirm TE compatibility?

So did the update and the initial problem with the first release is there still. Found the ORBX forum where they went through the steps on manually fixing the issue all to find that the Amsterdam_LC folder doesn't exist. Still attempted the steps but to no prevail. If I were you, I would hold off a bit.

[Steven Silva]

fly tampa thanks for the update, but I have thousands of problems with the update one of them is that when I am in gates, parkings, taxiways and runways I appear buried in them but when I move the plane towards the grass it takes me out of the mud caused in the aforementioned Previously, I definitely do not know what happens for now to return to the previous version of EHAM but in the same way thank you and enjoy those who have no problems

[blaunarwal]

Does this work directly with True Earth Netherlands or do we have to make the manual changes again ?

Thanks.

Regards, Gerard

Yep +1 ... Anybody can confirm TE compatibility?

+1, also need to know, what needs to be done for TE compatibility

[Ian S]

To prevent any issues I would suggest a full new install...

I would like to do a whole fresh install, but on the Fly Tampa downloads page, only the update is available. If I go to my purchase email, it leads me to a BMT Micro site, which states my password has expired? What is the easiest way to access a full download?
thanks

[Er!k]

Download the Universal Installer and fill your e-mail and serial there... Then it will automatically download the full v1.3 for you: http://www.flytampa.org/downloads.html

[tangjuice81]

When I install v1.3 my scenery has everything but the terminals. It reverts back to the default EHAM. Suggestion? Thanks in advance.

[skylane182]

Do you all have Amsterdam above FTX NL in your scenery library? I have and for me it works fine. Haven't tried all taxiways yet, but I can see all Flytampa buildings and no default buildings.

[tangjuice81]

Do you all have Amsterdam above FTX NL in your scenery library? I have and for me it works fine. Haven't tried all taxiways yet, but I can see all Flytampa buildings and no default buildings.

Thanks, I'll check for that. I noticed the ORBX EHAMxxx was still active so that could have been the issue as well .

[tangjuice81]

Do you all have Amsterdam above FTX NL in your scenery library? I have and for me it works fine. Haven't tried all taxiways yet, but I can see all Flytampa buildings and no default buildings.

Thanks, I'll check for that. I noticed the ORBX EHAMxxx was still active so that could have been the issue as well .

Fixed. For some reason the scenery would go below everything. Thanks!

[Skipy]

Im also wondering about SODE jetways in the new update

Yes we need SODE jetways as GSX level2 ones come with a modified AFCAD :-(.

[Brittanix]

For all Amsterdam die-hards, a little update to keep you going, ahead of the full v2 upgrade (coming soon)
This update comes as a full new installation. No prior version of Amsterdam is required.

I have a question regarding the upcoming v2:
Will the v2 upgrade need to be purchased separately, or will I be entitled to v2 upgrade if I have the current version?

Im not sure wether to buy now, or to wait until v2 comes out.

[emilios[flytampa]]

All users of current AMS version will be entitled to a discount upon v2 release

[Schlotterknie]

Is that update only for P3D v5 or for v4 as well?
The universal installer automatically installs into P3D v5. I can´t choose to install the P3Dv4 version...

Did I overlook something...?

[elButz]

I removed completely Amsterdam prior to installing 1.3 version. Going through taxiway Q I got launched in the air again. Also did not notice any changes in the Configurator for Amsterdam. Is it me doing something wrong here or you guys also experience the same?

same here, tried various configurations with FSGlobal 2020 (with/without AES, layer options above/below FT elevation entry, with ORBX Vector off/on, 1m/5m mesh res,...).

I'm still launching in the air, Drzewiecki's KJFK has the same problem, although there I usually only get tire smoke and not an insane launch like with EHAM. The new EDDM by SimWings works fine for me (also has bridges).

An optimization for 5m mesh res would be great, as I've got a lot of airports that require this to avoid double-landings...