Updated AFCADs for FlyTampa Copenhagen (Version 12)
- funkyj4ever
- Posts: 43
Re: Updated AFCADs for FlyTampa Copenhagen (Version 4)
I got problem like this people viewtopic.php?f=28&t=6963
when using this afcad v4 and have not actived aes on the airport
when using this afcad v4 and have not actived aes on the airport
Re: Updated AFCADs for FlyTampa Copenhagen (Version 4)
Using the same AFCAD and no problem at my end. So I can't help, sorry.
- funkyj4ever
- Posts: 43
Re: Updated AFCADs for FlyTampa Copenhagen (Version 4)
I got it fixed dont know how but i reset to default after a oom problem and the problem of the missing jetways is back. There must be something wrong
- funkyj4ever
- Posts: 43
Re: Updated AFCADs for FlyTampa Copenhagen (Version 4)
I think it has something to do with the jets_xxxx.bgls when i set jets_static.bgl to on the missing jetways are fixed but then some jets are duplicated. same for jets_random.bgl. I dont know what jets_staticbyx.bgl does. It says it is a monitor file?
- yes have the other afcads disabled
- yes repaired with aes and dont have it activated on ekch
- yes have the other afcads disabled
- yes repaired with aes and dont have it activated on ekch
- funkyj4ever
- Posts: 43
Re: Updated AFCADs for FlyTampa Copenhagen (Version 4)
I don't have AES as I'm a 100% P3Dv2 user, so therefore I couldn't help you as P3D aren't covered by AES. So I wouldn't have been to any help. And because of this I don't know how/if my AFCAD's works with AES.
- funkyj4ever
- Posts: 43
Re: Updated AFCADs for FlyTampa Copenhagen (Version 4)
I already fixed it!
Re: Updated AFCADs for FlyTampa Copenhagen (Version 4)
I installed this AFCAD and yes, the distribution to the gates is much better compared to the original file. However, I now use the "SW" variant and I realized that there is only one runway left (when selecting the airport inside FSX to put my plane). Is this the expected behaviour? In the original AFCAD, there were all runways available. Just wondering...
Re: Updated AFCADs for FlyTampa Copenhagen (Version 4)
Sorry for the late reply. Been busy RL.
Yes. It's expected. I've simply closed all runways for takeoff except the runway you could select. Otherwise FS would send the AI planes on the wrong runways, which wouldn't be very realistic at all.
If you use the NE file you would also only select 1 runway (the other parallel runway and on the opposite heading).
Yes. It's expected. I've simply closed all runways for takeoff except the runway you could select. Otherwise FS would send the AI planes on the wrong runways, which wouldn't be very realistic at all.
If you use the NE file you would also only select 1 runway (the other parallel runway and on the opposite heading).
Re: Updated AFCADs for FlyTampa Copenhagen (Version 4)
Hello Johan
Awesome afcad file work
And Works together with flytampa configurator
But after i have installed gsx and MT6.0 it seems that when i listen to atis
That both runway 22l and 22r for landing and for takeoff
Have you heard of that before
Maybe should i rechoose in the Configurator
Gsx May have done something
An exsamble Also is that traffic from mt6 lands on 22r
Hope an fix og solution can be found
Awesome afcad file work
And Works together with flytampa configurator
But after i have installed gsx and MT6.0 it seems that when i listen to atis
That both runway 22l and 22r for landing and for takeoff
Have you heard of that before
Maybe should i rechoose in the Configurator
Gsx May have done something
An exsamble Also is that traffic from mt6 lands on 22r
Hope an fix og solution can be found
Re: Updated AFCADs for FlyTampa Copenhagen (Version 4)
I don't have MyTraffic as I have my own AI.
I think GSX might have something to do with it. But I don't use GSX myself, so I can't make any fixes, sadly.
I think GSX might have something to do with it. But I don't use GSX myself, so I can't make any fixes, sadly.
Re: Updated AFCADs for FlyTampa Copenhagen (Version 4)
Hello everyone:)
I am also having problems with aircraft not landing on 22L. I tried changing things in the NE file with the ADE, but without success. My winds are set at 270 degrees (west). If I try the SE file, 04L/04R is used. I am using P3D v.2.5. Everything worked good in the previous EKCH version.
Any suggestions?
I am also having problems with aircraft not landing on 22L. I tried changing things in the NE file with the ADE, but without success. My winds are set at 270 degrees (west). If I try the SE file, 04L/04R is used. I am using P3D v.2.5. Everything worked good in the previous EKCH version.
Any suggestions?
Re: Updated AFCADs for FlyTampa Copenhagen (Version 4)
Haha your problem is what i need
Your problem is that you have to change afcad file In the flytampa configurator
Your problem is that you have to change afcad file In the flytampa configurator