St Maarten 1.1 Update (FS9)

[george[flytampa]]

i have the same problem with kbos v3 when i updated to v3.1 and with TNCM qhen i install this update please help me

thanks

Email support@flytampa.com to request a new installer. Make sure you use the name & email you 'bought' it with.

Then we can remove the boxes.

[Greg Goodavish]

Martin, I am having a problem with this update as well. With the original installer and the texture upgrades to change rwys to 10/28, all is fine, as shown by the snapshot. Nice, flat ground to the sides of the runway. As soon as I add update to version 1.1, I get hills on both sides of the rwy. Obviously, something is not installing right with the update. Can you advise what to do?

This pic is before the update:


This pic is after the update:

[martin[flytampa]]

Check if you have this file:

Addon Scenery/FlyTampa-Maarten/scenery/maarten_flatten.bgl

[Greg Goodavish]

Yes, I have that file. Any other ideas? It has to have something to do with what the update does, as it works fine before the update.

[martin[flytampa]]

Yes, I looked through what the installer does and don't see anything suspicious. Because this has been out for years I am assuming it is some unique problem. Please email me your name and I'll send you the regular 1.1 installer. This has also been distributed for years now without this problem report.

[Greg Goodavish]

Thanks, Martin. I have sent you an email to the support email address, with my email address included. Thanks.

[Greg Goodavish]

Martin, I also tried to delete and then reinstall the scenery, to see if that would help. I read the docs, and noticed that it said two files would be renamed to FL931250.original & HP931250.original in the FS9/scenery/name/scenery folder. Those two renamed files were not there, just FL931250 and HP931250. Could that be an issue that is causing this? Perhaps those two files were never installed/converted?

[martin[flytampa]]

Martin, I also tried to delete and then reinstall the scenery, to see if that would help. I read the docs, and noticed that it said two files would be renamed to FL931250.original & HP931250.original in the FS9/scenery/name/scenery folder. Those two renamed files were not there, just FL931250 and HP931250. Could that be an issue that is causing this? Perhaps those two files were never installed/converted?

The FL and HP file are likely to cause such a problem. But these are untouched by the update, the main installer is what backs them up and modifies them.

Normally after installing you will see:

FS9/scenery/Name/scenery/FlyTampa_Maarten_Backup/

with 4 files in that folder. The file HP931250.bgl should be 57KB for example. If you look in the parent folder /scenery/ the same file HP931250.bgl should have the same size 57KB.

If the scenery is ever transfered to a new FS installation without using the installer, these files would be missing of course.

[martin[flytampa]]

Disregard my last post. I just noticed you have the standalone TNCM, so the HP/FL files don't apply.

I'm emailing you a new installer.

[Greg Goodavish]

That did the trick, Martin. All is good now. Thanks for all your help!

[nickac1092]

[quote="martin[flytampa]"]You need a new copy/installer. Email me your name and I'll send you a replacement.[/quote]
Ive got the textures working for the runway but i get the gray box on the side of rwy 10 just like that picture shows. I would love to have it fixed soon.

[teodc6@hotmail.com]

Hello to everyone,I installed the St Maarten 1.1 Update (FS9) but there is no change to new RWY 10/28
Could you please inform me,how to change if it is possible, perhaps manually, St -Maarten FS9 to RWY 10/28 .
Thanks ,Teo

[Er!k]

Hi Teo, have you seen this topic: viewtopic.php?f=14&t=3720