Sidney YSSY for P3Dv5.1

[dom66]

Hello, I have your Sidney YSSY scenery on P3Dv5. I am really disappointed by this scenery which does not look like the usual quality expected from Fly Tampa. The flaws are too great, and I will tell you a few. Double indications at the start of the Runway example 16R in duplicate. No correct gate example 2 screenshots take-off crash on track 16R for example in the rain of Active Sky: Watch the video, 16R on ground !! And the takeoff crash

"As I can not pass the images and the video on the forum here is the message that I have
Error: Newly Registered Users may not post Links or Spam." ???

excuse my bad English

[dom66]

Here my vidéo>>>Cherche on Youtube for "Take-off Sydney 16R Fly Tampa P3Dv5"

[george[flytampa]]

I don't really understand your problems. It sounds like you might have duplicate sceneries or afcads installed if you are seeing double items?

Is this your video?
https://www.youtube.com/watch?v=v_dPItf ... el=DomBarh

You have at least three sceneries running. I can see V1 of Flytampa Sydney, the stock Microsoft Sydney and I presume you have installed Flytampa Sydney V2 installed too.
Go into the scenery library and uninstall V1 at least.

[dom66]

I don't really understand your problems. It sounds like you might have duplicate sceneries or afcads installed if you are seeing double items?

Is this your video?

You have at least three sceneries running. I can see V1 of Flytampa Sydney, the stock Microsoft Sydney and I presume you have installed Flytampa Sydney V2 installed too.
Go into the scenery library and uninstall V1 at least.

Yes that's my video on track 16R I installed Sydney Update for P3Dv4 bought at $ 12.99 because I had the scenery for FSX.

In the P3D library, I have FlyTampa Sydney V2 but no V1 ??
I don't have Microsoft on my Computer, so you can't see the Microsoft Sydney stock, or it's the P3D Sydney stock.

For the gates the images are at your disposal How to solve this problem? Is the Sydney V2 update complete? And don't need the previous version ??

[george[flytampa]]

The microsoft sydney comes with p3d. I can clearly see it all over your video.

Just remove sydney from the scenery library. It should only be listed under addons.

[dom66]

The microsoft sydney comes with p3d. I can clearly see it all over your video.

Just remove sydney from the scenery library. It should only be listed under addons.

Ok if I delete Sydney, and then I have what? Just Microsoft Sydney stock????

Here is the proof of my purchase.
Dear Dominique BARBONI,

Thank you for purchasing FlyTampa-Sydney V1 to V2 Upgrade

Your new V2 serial key is:

To install into Prepar3Dv4 or Prepar3Dv5, use the link below:
https://www.flytampa.org/dwl/FlyTampa_U ... _Setup.exe

[george[flytampa]]

No, if installed correctly, Sydney shows up under Addons. Not in the scenery library.
It looks like you have both the old and new scenery installed. You need to uninstall the old one.

[dom66]

I told you I didn't have the old one.

All my FlyTampa scenes are in LM \ Prepar3Dv5 \ FlyTampa \ and not in AAd ON nor in Addon Scenery.
The installations are done automatically, I did not intervene.
As I cannot show you screenshots (refused by FlyTampa) it is difficult to explain.

[george[flytampa]]

in your video, I can see older puddles on the runway only used in the OLD scenery.

[dom66]

No, if installed correctly, Sydney shows up under Addons. Not in the scenery library.
It looks like you have both the old and new scenery installed. You need to uninstall the old one.

OK I found it, I disabled Sydney in addon, I will see the result. I will come back to the forum tomorrow

[george[flytampa]]

Hey Dominique,

Tried to email you but your ISP is refusing to take any incoming mail.
Your serial is working. Make sure you aren’t pasting it with blank spaces at the front or the end. If that fails, try typing it in manually.

[dom66]

Hey Dominique,

Tried to email you but your ISP is refusing to take any incoming mail.
Your serial is working. Make sure you aren’t pasting it with blank spaces at the front or the end. If that fails, try typing it in manually.

Hello George,
After uninstalling all of YSSY's residue, I followed the reinstallation instructions to enter the key manually and successfully reinstalled the scenery. I found the scenery with the usual qualities of FlyTampa. Thank you for your help. Well to thank you, I'll move on to buying a new scenery, even if I don't need it.

For my incoming mail, I do not understand, because I receive all the mails as usual.

For the crash in the rain, Active Sky is responsible, because if I deactivate AS, no more crashes on takeoff????

Thank you again for your help. I will remove my video from youtube.
*One question, after how much seniority one can pass links for image and video??
You can close this ticket

Best regards
Dominique